1. Do you know what is "energy harvesting"?

Most passive RFID tags simply reflect back waves from the reader. Energy harvesting is a technique in which energy from the reader is gathered by the tagged, stored momentarily and transmitted back at a different frequency. This method may improve the performance of passive RFID tags dramatically.

2. Do you know what is tag collision?

Another problem readers have is reading a lot of chips in the same field. Tag collision occurs when more than one chip reflects back a signal at the same time, confusing the reader. Different vendors have developed different systems for having the tags respond to the reader one at a time. Since they can be read in milliseconds, it appears that all the tags are being read simultaneously.

3. Do you know what is reader collision?

One problem encountered with RFID is the signal from one reader can interfere with the signal from another where coverage overlaps. This is called reader collision. One way to avoid the problem is to use a technique called time division multiple access, or TDMA. In simple terms, the readers are instructed to read at different times, rather than both trying to read at the same time. This ensures that they don't interfere with each other. But it means any RFID tag in an area where two readers overlap will be read twice. So the system has to be set up so that if one reader reads a tag another reader does not read it again.

4. Do you know the difference between read-only and read-write tags?

Microchips in RFID tags can be read-write or read-only. With read-write chips, you can add information to the tag or write over existing information when the tag is within range of a reader, or interrogator. Read-write tags usually have a serial number that can't be written over. Additional blocks of data can be used to store additional information about the items the tag is attached to. Some read-only microchips have information stored on them during the manufacturing process. The information on such chips can never been changed. Other tags can have a serial number written to it once and then that information can't be overwritten later.

5. Do you know how much information can the tag store?

It depends on the vendor and the application, but typically a tag would carry no more than 2KB of data-enough to store some basic information about the item it is on. Companies are now looking at using a simple "license plate" tag that contains only a 96-bit serial number. The simple tags are cheaper to manufacture and are more useful for applications where the tag will be disposed of with the product packaging.

6. Do you know what is an Electronic Product Code?

The Electronic Product Code, or RFID, was developed by the Auto-ID Center as a successor to the bar code. It is a numbering scheme that will be used to identify products as they move through the global supply chain. For more on EPC technology.

7. What is Passive tags in RF Engineering?

One problem encountered with RFID is the signal from one reader can interfere with the signal from another where coverage overlaps. This is called reader collision. One way to avoid the problem is to use a technique called time division multiple access, or TDMA. In simple terms, the readers are instructed to read at different times, rather than both trying to read at the same time. This ensures that they don't interfere with each other. But it means any RFID tag in an area where two readers overlap will be read twice. So the system has to be set up so that if one reader reads a tag another reader does not read it again.

8. What is active tags in RF Engineering?

Active RFID tags have a battery, which is used to run the microchip's circuitry and to broadcast a signal to a reader (the way a cell phone transmits signals to a base station).

9. Tell me did all countries use the same low-, high and ultra-high frequencies?

Most countries have assigned the 125 kHz or 134 kHz area of the radio spectrum for low-frequncy systems, and 13.56 MHz is used around the world for high-frequency systems. But UHF RFID systems have only been around since the mid-1990s and countries have not agreed on a single area of the UHF spectrum for RFID. Europe uses 868 MHz for UHF and the U.S. uses 915 MHz. Until recently, Japan did not allow any use of the UHF spectrum for RFID, but it is looking to open up the 960MHz area for RFID. Many other devices use the UHF spectrum, so it will take years for all governments to agree on a single UHF band for RFID. Government's also regulate the power of the readers to limit interference with other devices. Some groups, such as the Global Commerce Initiative, are trying to encourage governments to agree on frequencies and output. Tag and reader makers are also trying to develop systems that can work at more than one frequency, to get around the problem.

10. Do you know which frequency is right for your application?

Different frequencies have different characteristics that make them more useful for different applications. For instance, low-frequency tags are cheaper than ultra high frequency (UHF) tags, use less power and are better able to penetrate non-metallic substances. They are ideal for scanning objects with high-water content, such as fruit, at close range. UHF frequencies typically offer better range and can transfer data faster. But they use more power and are less likely to pass through materials. And because they tend to be more "directed," they require a clear path between the tag and reader. UHF tags might be better for scanning boxes of goods as they pass through a bay door into a warehouse. It is probably best to work with a consultant, integrator or vendor that can help you choose the right frequency for your application.

Download Interview PDF